Replace Parts for CKD-Cfla-40 CO2 Laser Source

• After-sales Service: Online (Free) or to Door (Need to Pay )
• Warranty: 12 Month
• Customized: Non-Customized
• Shipping Cost: Estimated freight per unit.: about shipping cost and estimated delivery time.
• Currency: US$
• Return&refunds: You can apply for a refund up to 30 days after receipt of the products.
• Model NO.: CKD-CFLA-40 CO2 Laser Source
• Standard Component: Standard Component
• Type: Laser Source
• Voltage: 48V
• Maximum Current: 12.5A
• Wavelength: 10.6um
• Cooling Mode: Air-Cooling
• Transport Package: Carton
• Specification: CO2 laser source
• Trademark: CKD LASER
• Origin: China
• HS Code: 9013200099
• Production Capacity: 50 PCS/ Month
• Package Size: 54.00cm * 25.00cm * 22.00cm
• Package Gross Weight: 8.500kg

Product Description

This laser is specialized for CKD-CFLA-40, belongs to repair parts beyond warranty.
 

TECH DATA

Data of laser source:

System performance indicators	wavelength	106μm
	Rated output power	≥40W
	Power stability	<±6%
	Mode quality	M2<1.3
	Beam diameter	1.8±0.2mm
	Beam divergence angle	7.5±0.5mrad full angle
	Ellipticity	<1.2:1
	polarization	Linear polarization (>100:1) parallel to the width direction
	Operating frequency and duty cycle	0-25KHz, 0-100%DC
Specifications and usage conditions	weight	7kg net weight, 8.5Kg gross weight
	size	Net size: 357*92.5*142mm, packing size:540*250*220mm
	Like voltage	48VDC±2%,Maximum current is 12.5A
	thermal load	<600W
	Maximum shell temperature	<60ºC (140°F)
	Working environment temperature	5ºC-40ºC (41°F-104°F)
	Working height	<2000m (6, 500ft.)
	humidity	non-condensing
	Shipping and storage environment	-10 ºC -60 ºC (14 ° F-140 ° F)non-condensing

Notice:
1.Laser power is tested according to the temperature of laser which is 25ºC,every time the laser temperature rises 1ºC,the output power will reduce 1%.
2.Definition of stabilization: ±(Pmax-Pmin)/(2Pmax).
3.Testing condition of stabilization: Warming up about 10mins, controlling duty cycle constantly, under the normal operating environment.

APPLICATION

Installing inside the laser path of laser coding machine like below:

What material this laser source can be used for?



Dimension figure:


Wiring way of RJ-45:

Connector	Wiring instruction	Signal instruction
8	Correspond marking or cutting card of PWM positive signal	RF Enabled
6	2 and 6 short circuit	Laser status output TTL Logical output:0=Laser ok,1=Laser fault
2		Control enabled TTL Logical input:0=laser control enabled,1=Laser control off
1,3,4	Correspond marking or cutting card of PWM signal ground	GND
Notice: 48V 30A power supply required grounding Note the dust protection of the laser output window. Prevent the lens from burning due to dust particles. Especially the way laser output window faces up. Be careful to prevent backward reflection, any backward reflection can cause laser damage. We suggest that the front and back end of the laser shouldn't be all fixed at the same time, avoid the deformation of the cavity of the laser cavity due to the stress caused by the heat expansion and shrinkage of the material The fan is inhaled, there must be enough space (greater than 3CM) around the radiator to heat the air, clean the fan in time to ensure good ventilation. If there are any problems during the usage of the laser, please contact us for your timely solution.